|
|
|
| NEWEST ON EBAY THERE HERE THE SF95C+ MODEL SERIES NEW |
| Category:
Consumer Electronics
/
Satellite, Cable TV
|
 |
| Start Price: |
USD 14.99 |
Click Here
to See More
|
| Current Price: |
USD 14.99 |
| Reserve Price: |
- |
| Time Left: |
- |
| Bid Count: |
0 |
| Buy It Now Price: |
- |
| Start Time: |
11/20/2008 |
| End Time: |
11/23/2008 |
| Location: |
West Wyoming, Pennsylvania |
|
SquareTrade © AP6.0 SF-95c+ Satellite Finder signal meter, FTA,DTV,DISH a.imagelink {color:#000000;} a:hover.imagelink {color:#000000;} a:visited.imagelink {color:#333333;} a.imagelink img.auctionimage { border: 2px solid #000000; } a:visited.imagelink img.auctionimage { border: 2px solid #333333; } YOU ARE BIDDING ON 1 SIGNAL METER ***COMES WITH LIGHT AND TONE FOR EASY INSTALLS*** ~FALL SALE~ 2009 Model Series - SF-95C+ SATELLITE METER ~buy from a authorized dealer~ **FREE DISH PRO ALIGNMENT SOFTWARE** CLICK HERE---->>>>http://www.visionplus.us/satcalc.html <<<<------CLICK HERE Works on all satellites HD, DTV, FTA, Dish Network, Voom, Bell Express vu, C band, high speed internet satellites as well SF-95c+Satellite Finder Dish Alignment Tool"accept no cheap imitations"Now with H/V and 22KHz indicators SF-95c+ is a satellite finder that helps to make precise dish set-up easily. Its ultimate sensitivity will indicate 0.2 dB level difference in 950 to 2050MHz. SF-95c+ is miniature (3.03" x 2.36" x 1.10") and light weight (95 gm) SPECIFICATIONS : MODEL INPUT FREQ IMPEDANCE MIN. INPUT MAX. INPUT POWER SIZE SF-95c 950-2050 MHz 70 Ohm -40 dB m -10 dB m 13-18 V 77 x 60 x 28 mm INSTUCTIONS: SATELLITE FINDER MODEL SF-95, SF-95c, & SF-95c+ OPERATION: 1. Unplug the receiver from the wall. 2. Remove the coax from your LNBF. 3. Connect the coax to the SF-95 meter to the connection that says "TO REC". 4. Using a jumper coax connect to the side of the meter that says "TO LNB". 5. Connect the other end of the jumper coax to the LNBF. 6. Plug in and power up your receiver. 7. Adjust the signal level knob on the front of the meter so the reading is below 5 on the scale. 8. Do a rough adjustment for the azimuth and elevation of the dish to get a starting point. If you don't know the azimuth and elevation settings you can use SatCalc to find your values. SatCalc is free to use and can be downloaded at http://www.visionplus.us/satcalc.html Full ViewLike to have it on your desktop? 9. With your signal level at or below 5 on the meter, start to adjust the dish very slowly while watching the meter. If the meter level goes above 5, adjust the knob on the front of the meter to make the meter read at or below 5. Repeat as needed. 10.Once you have found the satellite and have peaked it to the highest possible level, go to the receiver and confirm that you are on the right satellite. 11.If you are using a linear LNBF: After confirming the satellite is correct, adjust your LNBF by turning it in the holder first to the right and then to the left watching the meter and stopping at the highest point in signal. 12.Power down the receiver by unplugging the power cord. 13.Remove the meter and re-connect the coax from the receiver to the LNBF. 14.You are now ready to power up your receiver. IMPORTANT NOTES: • SF-95c: If you are using the SF-95c you will notice a small compass built into the side of the meter for finding your azimuth. • SF-95c+: If you are using the SF-95c+ in addition to the compass, you will notice indicator lights for verifiying that your receiver is set to Horizontal or Vertical polarity and if 22KHz tone is on or off. • Green H/V light indicates Vertical Polarity. • Red H/V light indicates Horizontal Polarity. • Red 22KHz light indicates 22KHz is ON. • When aligning a C-band dish do not use your meter in front of the dish to avoid full scale readings. • When connecting to a LNBF with gain higher than 65dB, insert a 5dB attenuator between the meter and the LNBF. If a attenuator is not available you may use a long coax (60 feet or more) between the meter and the LNBF. • If the meter needle is jumping the sensitivity is too high. Adjust the S.A. level on the back of the meter by punching through the label where marked. Be very careful not to damage the adjustment by turning it too far or too hard. SPECIFICATIONS: • Frequency Range: 950 ~ 2300 MHz • Input Level: -25dBm ~ -75dBm • Gain: 11 ~ 15dB • Sensitivity(S.A.): 7 Microvolt • Power Supply: +13/+18V DC • Operating Range: -52 ~ -65dB (LNBF Gain) Do not bid until you read and 100% agree with our "terms of sale" SHIPPED WITHIN 24 HOURS (NOT ON WEEKENDS) AND WITH CONFIRMATION NUMBER-ONLY THE USA SHIPPING ANYWHERE " PAYPAL " ONLY AND "POSTAL MONEY ORDER" FOR SECURITY FOR THE BUYER AND THE SELLER THANK YOU FOR STOPPING AND LOOKING AND DONT FORGET TO LOOK AT MY OTHER AUCTIONS On Nov-07-07 at 12:37:47 PST, seller added the following information: SquareTrade © squaretrade warranty v2.0 On Apr-12-08 at 10:27:03 PDT, seller added the following information:
Place a Bid!
|
HOME
|
|